1080
Chrome Throttle Clamps and Tube Set feature smooth
design, upper and lower pieces with screws and nylon throttle
tube, for single or dual cable application. For use with 1982-up
type cables.
VT No.
Type
35-0253 Single
35-0254 Dual
35-0253
35-0254
Throttle
1. Cut 2³⁄₈” off end of handlebar. Remove end of throttle handle
that would attach to throttle cables.
2, Mark handlebar for inner throttle sleeve. Drill a hole for the set
screw, this will hold throttle on the handlebar.
3. Remove set screw from the outer sleeve of spiral. Slide grip on
& mark end of grip on the handlebar. Measure from this mark back
to set screw in outer sleeve. This measurement will be used to
mark & drill the throttle grip. Once drilled install grip. Use a small
amount of Loctite® on set screw for final installation.
4. Note Set Screw (A) do not tighten so as to make contact with
handlebar it will prevent throttle from turning.
Internal Throttle
36-0570
Internal Throttle/Clutch Unit features ball and needle bearing
construction with built in return spring.
VT No. Type Item
36-0575 Throttle Assembly Uses 3 types of bearings
36-0598 (4), 36-0591 (1), 36-0590 (1)
36-0789 Clutch Assembly
36-0591 Bearing ³₈ x ⁷₈ x ⁹₃₂
Inner Sleeve
A
36-0575
36-0789
Anderson Motorcycle Supply
Patch. VT No. 48-1358
Flanders Patch.
VT No. 48-1787
Original Jack Hammer Handlebar Grips include grip. Thick
black rubber. 1960’s style.
VT
No.
Type
Size
35-0071 Grip Throttle
28-0786 Grip Set with tube
28-0116 Grip Set
35-0347 Grip Kit
28-0002 Brown
28-0003 Red
28-0004 White
28-0182 Grip
Set
7/8”
35-0261 Grip & Throttle 7/8”
35-0832 ¹⁄₄ Turn
7/8”
35-0779 ¹⁄₄ Turn
1”
36-0152 ¹⁄₄ Turn 1” (Complete Kit)
28-0002
28-0003
28-0004
28-0786
28-0116
35-0261
35-0832
35-0255
36-0564
36-0790
Electronic Throttle Assembly with gear and wire for Touring
models with “TBW” throttle by wire.
VT No. Item
Fits
36-0790 Throttle Assy 2008-15
36-0791 Throttle Assy 2016-up
35-9871 Repl. Tube
35-9871
36-0791
35-0779
Throttle by Wire Handlebar Wiring Extension Kits include
factory type connectors for easy assembly.
VT No. Length Fits
32-6651* One Size 2008-13 FLHT, FLHT, FLHX
32-6687* One Size 2014-15 FLT
32-6688 +8”
2016-up FLT, FXST, FLST
32-6689 +15
2016-up FLT, FXST, FLST
*Note: 18” Extended Throttle by Wire Harness Only.
32-6651
36-0152
VT No. 36-0570 Internal
Throttle Sleeve. Custom
design allows pull action of
throttle cable for use with billet
grips.
VT No. 36-0570
Throttle Housing custom design for single cable operation.
Single Dual Finish
36-0151
Chrome
35-0856 Black Vintage
35-0857
Chrome Vintage
35-0858
Copper Vintage
35-0865 Cable Black
35-0255
Accepts a 1982-1995 throttle cable
36-0564 Chrome Dual Cable Throttle housing is 1”
with 1/4-20" thread, and is for use with idle and throttle cable.
35-0856
36-0151
35-0858
35-0857
35-0865