1276
Lapping Tool
16-0039
16-0135
Combination
Motor
VT No.
# Use
Model
Years
16-0135
C Engine Big Twin
1936-up
16-0039
A Combo C and B
As Above
16-0012
All
Spanner Wrench
16-0204
Pilot Set
Lapping Tools used for precision alignment of engine and transmission shafts.
Engine unit replaces 96710-40 to lap right and left crankcase races for oversized
bearings. Transmission tool insures proper fitting of oversized rollers with main-
shaft races on Big Twin and Sportsters. The dual-purpose “Combo Lap” for both
engine and transmission is also available. Rod laps not included.
Transmission Lap Head
includes pilot. For Eastern
tool only.
VT No. Size Model
16-0020 1.870 Big Twin
74 and 80
16-0019 1.300 1957-85
Sportster
Lap Head Pilots, sold each. For Eastern tool only.
VT No. OEM
Type
Years
16-1724 96727-56 Motor
1955-up Big Twin
16-1725 96728-56 Motor
1954-76 XL
16-1726 96715-40 1½ Motor 1930-54 Big Twin
16-1727 96716-40 Motor
1955-57 45”,
Big Twin
16-1832
Motor
1987-up XL
16-0216 Pilot Shaft Only
16-1724
16-1724
16-0018
16-0032
16-0026
16-0025
16-0034
16-0022
Replacement Lapheads are sold each. For Eastern
tool only.
Laphead Pilot# Type
Fits
16-0032
1.750”
Engine
1958-up Big Twin
16-0026
1.50”
Engine
1940-54 Big Twin
16-0025
1.375”
Engine
1954-76 Sportster
1955-57 Big Twin
1929-73 45”
16-0018
1.562”
Engine
1987-up Sportster
16-0034
1.870”
Transmission 1936-77 Big Twin
16-0024
1.300”
Transmission Sportster
16-0022
1.6250” Rod
Big Twin XL
16-0021 1.50” Rod
45”
16-0020
16-0019
16-0024
16-0021
1958-98 Big Twin Case Lap Tool features
a lap which is supported on both sides by
a pilot on the bushing side and plate which
locates on the case pins of the cam cover,
by Jims. Order lap and pilot VT No. 16-0881
for 1937-early 77 4-speed main race sepa-
rately.
VT No.
Item
16-1835
Big Twin Case Lap Tool
16-0893
Case Lap Head only
16-1039
Motor Number Stamp Set for FL mod-
els.
VT No.
Year
16-1039
1936-47
16-1264 1950-69
16-0423 1970-99
16-1147
Holder
16-0423
16-1264
Jims Twin Cam Case Support Block for Balancer.
Engine 1999-2017 FXST, FLST, FXD and 1999-2016
FLT. These blocks properly support the case on a
level plane when using a press for work.
VT No. 16-1916
Main Bearing End Plug Tool allows the setting of proper end play in Big Twin
Timken Bearing Assemblies by selection of proper spacer from the catalog. Use
when refitting bearings or bearing sets on late models when spacers are not
included. Not needed for our VT No. 12-0309 or 12-0310 Timken sets, these are
pre-spaced from the factory.
VT No.
Fits
16-1795
1955-98 Big Twin
16-1796
1977-03 XL
16-1796
16-1795
16-0518
Left Rear Engine Mount Bolt Wrench allows
removal and installation of left rear motor mount
bolt on Big Twins without removing the inner pri-
mary cover.
VT No. 16-0518