1278
Pinion Tool
1991-99 Crankshaft Locking
Tool fits XL models by engag-
ing the pinion shaft splines. This
allows removal and torquing of
the pinion nut during installa-
tion. Replaces 41506.
VT No. 16-1055
Crankshaft Locking Tool locks
locks all crankshafts by engaging
the pinion shaft splines. This allows
removal and torquing of the pinion
nut during installation. Fits 1999-17.
VT No. 16-1672
Pinion Gear Lock Tool
fits 1954-98 Big Twin,
when applying torque to
pinion nut. By Jims.
VT No. 16-0659
Jims Sportster Crankshaft Locking Tool. Use on
Pinion side of all 1991-up XL to keep crankshaft assem-
bly from rotating during assembly on valve train repair.
VT No.
Fits
16-1666 1991-2002
16-1665 2003-up
Pinion Shaft Race Installer fits 1977-E81 Sportster models.
Replaces 97080-77A.
VT No. 16-0965
Big Twin Pinion Bearing Race
Removal and Installation Tool
is used to remove and install the
outer race on 1958-98. Replaces
39958.
VT No. 16-0648
16-1672
Jims TC Crankshaft Guide use to
spread pinion bearing rollers while reas-
sembling right side engine case on to
flywheel assembly. Use on 1999-17 Twin
Cams.
VT No. 16-1281
A
16-0129
Pinion Gear Puller with collars, used to remove and install pinion gear on 1984-
98 Big Twins and 1976 and earlier XL. Order nut wrench separately.
VT No. Brand
# Item
16-0129 VT
A Puller Kit
16-0162 Jims
B Puller Kit
16-1060 Sifton
B Puller Kit
16-0406 VT
C Collar Set
16-0141 VT
D Nut Wrench
16-0168 Jims
D Nut Wrench
16-0747 Motorshop Puller Wrench Set
D
C
16-0747
16-1850
16-0150
Shaft Turning Tool fits spline or taper on assembled
motor and allows engine to be turned over by ½”
ratchet or impact driver. Sifton unless noted.
VT No.
Years
Type
16-0150
1930-54
Big Twin, Taper
16-1850
1955-05
Big Twin, Spline
16-1378*
2006-up
FXD, 2007-up FL, FXST
16-1852
1957-up
XL, Spline
*Note: Jims
16-1378
16-1852
16-0153
16-0888
16-1754
1955-up Sprocket Shaft Hard
Cap protects shaft when using
press. By Jims.
VT No. 16-0666
Twin Cam 24 Tooth Crankshaft Rotating Wrench for
use on all 2006-up Big Twins with 24T spline sprocket
shaft to check engine timing and parts clearance.
VT No. 16-9280
Sprocket Shaft Tool
Timken Bearing Removers remove bearing from
shaft without removing shaft from flywheels.
VT No.
Fits
16-0667
1957-76 XL
16-1833
1977-03 XL
16-1834
1955-85 Big Twin
16-1834
16-0667
16-1833
Sprocket Shaft Timken
Bearing Inner Race
Puller fits 1952-76 XL.
VT No. 16-1758
16-1758
Jims Twin Cam Right Crankcase Bearing Tool designed to
remove and replace the right crankcase bearing in and out with no
damage to crankcase. Use on 1999-17 Twin Cams.
VT No. 16-1275
16-1275
16-0162
16-1060
16-0129
B
Sprocket Shaft Seal and Lock Installers for Big Twins.
VT No.
OEM
Years
Application
16-0153 97235-55B 1955-69
Installs Nut and Seal
16-0888 97235-55B 1955-69
As Above, Jims
16-1754* 39361-69 1970-16
Installs seal only, Jims
16-1184
2017-up M-8
*Note: Use with 16-0140 or 16-1836 to install seal.
16-1184