Tools for TC-88
16-0791 16-0792
16-0790
16-0790
Jims Camshaft Remover and Installer Tool allows removal and installation of cams in the TC-88 model engine. Tool is used in conjunction with VT No. 16-0793 cam chain tensioner unloader.
VT No Price
16-0792
$182.00
Jims Crankshaft Bushing Remover/Installer will facilitate removal and installation of bushing in cam support plate on TC-88 model engines.
VT No Price
16-0791
$132.00
Jims Camshaft/Crankshaft Locking Tool will lock the gear teeth on the TC 88 model engine. Instructions included.
VT No Price
16-0790
$62.00
16-1365
16-1287
Jims Cam Chain Tensioner Unloader will hold the tension of the primary cam chain on the TC 88 model engine. Instruction included.
VT No Price
16-0793
$58.00
16-0793
Jims Powertrain Alignment Tool aligns powertrain to proper position safely and easily on most touring models. Performing alignment service must be done when engine, transmission or swingarm has been repaired or removed. This tool helps to provide the accurate alignment necessary for handling safety and performance. For 1993-97 FLHT; FLHR; FLHX & FLTR.
VT No. Price
16-1365
$710.00
Jims TC-88 Cylinder Torque Plates lasered with correct torquing sequence and will also work on Screamin' Eagle Big Bore Cylinders.
VT No Price
16-1287
$453.00
16-1051
16-1278
16-1366
Jims TC-88 Connecting Rod Bushing Tool use to remove and replace wrist pin bushing without removing connecting rods from crankcase.
VT No Price
16-1051
$132.00
Jims TC-88 Inner Cam Installer positions the two inner cam needle bearings and perfectly aligns to the shaft bores for a precision press fit.
VT No Price
16-1278
N/A
Clutch Assembly Service Tool will safely disasemble and assemble the clutch shell assembly and also remove and install the clutch hub from the bearing. Safe removal & installation of clutch shell ball bearing (OEM# 37906-90) with damage to new bearing.
VT No. Price
16-1366
$395.00
16-1367
16-1279
Inner Primary Cover Bearing & Seal Remover Installer Tool safely removes and installs inner primary bearing (OEM# 9135) without damage to the new bearing by pushing on the outer perimeter of the bearing. Removes and installs inner primary and seal that the transmission mainshaft passes through (OEM#12052A). For L1984-06 FXST/FLST; 85-06 FLT/FLHT/FXR/FXD/FXDWG
VT No. Price
16-1367
$175.00
16-1280 Jims TC-88 Cam Bearing Puller used to remove bearing from camshaft, this tool is designed to
Jims TC-88 Inner Cam Bearing Remover replaces inner bearing easily without damage to crankcase and also prevents rollers from falling into crankcase. Use on TC-88.
VT No Price
16-1279
$168.00
Jims TC-88 Camshaft Bearing Tool designed to remove and replace the right crankcase bearing in and out with no damage to crankcase.
VT No Price
16-1275
$181.00
16-1275 remove the bearing straight with no slipping or binding. Use on all TC-88.
VT No Price
16-1280
$228.00
Starter Ring Gear Rivet Fixture Tool removes the starter ring gear rivets from Big Twin clutch shells. For 2006-07 BT except Dyna.
VT No. Price
16-1368
$403.00
16-1368
Jims TC-88 Crankshaft Guide use to spread pinion bearing rollers while reassembling right side engine case on to flywheel assembly.
VT No Price
16-1281
$44.00
16-1281
1234

PRIVACY AND POLICIES

HTML content Copyright ©2012 Mas Classics-Vintage American Motorcycle Parts All rights reserved www.masclassics.com JPG images Copyright ©2010 by Tedd Cycle, Incorporated. All rights reserved. No part of this publication may be reproduced without prior written permission of the publisher.V-Twin MFG. Brand Products - Tedd Cycle Inc, Box 473 Vails Gate, NY 12584